F2 on a Gree heat pump: Solar kit-water flow switch
Short answer
On a Gree heat pump, F2 means: Solar kit-water flow switch. The manual does not say whether the heat pump stops. An engineer is needed to fix the cause. The wording differs by model range — each is shown below.
Reviewed 23 September 2026 · 4 sources
What it means
On the Versati III Monobloc (R32)
The manual says: Solar kit-water flow switch.
Part involved: water flow switch, circulation pump, water temperature.
On the Versati III Split / All-in-one (R32)
The manual says: Economizer inlet temperature sensor.
Part involved: temperature/pressure sensor.
On the Versati IV Split / All-in-one (R32)
The manual says: Economizer inlet temperature sensor.
Part involved: temperature/pressure sensor.
On the Versati V R290 Monobloc
The manual says: Economizer inlet temperature sensor.
Part involved: temperature/pressure sensor.
Is it safe?
On the Versati III Monobloc (R32)
| Does the heat pump stop? | Not stated |
|---|---|
| Engineer needed? | Yes |
The manual does not say whether the heat pump stops.
Resetting itself: unknown.
On the Versati III Split / All-in-one (R32)
| Does the heat pump stop? | Partly |
|---|---|
| Engineer needed? | Yes |
The heat pump keeps running with some functions stopped.
Resetting itself: unknown.
On the Versati IV Split / All-in-one (R32)
| Does the heat pump stop? | Partly |
|---|---|
| Engineer needed? | Yes |
The heat pump keeps running with some functions stopped.
Resetting itself: unknown.
On the Versati V R290 Monobloc
| Does the heat pump stop? | Partly |
|---|---|
| Engineer needed? | Yes |
The heat pump keeps running with some functions stopped.
Resetting itself: unknown.
What you can check
On the Versati III Monobloc (R32)
- Note the code shown on the controller and the unit model numbers (on the rating plate label) before contacting your installer.
- Check the heat pump's breaker/isolator at the consumer unit is on; do not open any casing.
- Check the heating system pressure gauge shows the pressure your installer set (typically about 1-2 bar); if it is low, report it rather than refilling unless you have been shown how. Check any filling loop is closed.
- Check radiator valves / underfloor zones are open and thermostats are calling for heat.
- In freezing weather keep the heat pump powered on (its frost protection relies on power) and check the outdoor unit is clear of snow/ice.
On the Versati III Split / All-in-one (R32)
- Note the code shown on the controller and the unit model numbers (on the rating plate label) before contacting your installer.
- Check the heat pump's breaker/isolator at the consumer unit is on; do not open any casing.
- Check the controller display is lit; a single power cycle at the isolator may be tried only if your installer or manual allows it.
On the Versati IV Split / All-in-one (R32)
- Note the code shown on the controller and the unit model numbers (on the rating plate label) before contacting your installer.
- Check the heat pump's breaker/isolator at the consumer unit is on; do not open any casing.
- Check the controller display is lit; a single power cycle at the isolator may be tried only if your installer or manual allows it.
On the Versati V R290 Monobloc
- Note the code shown on the controller and the unit model numbers (on the rating plate label) before contacting your installer.
- Check the heat pump's breaker/isolator at the consumer unit is on; do not open any casing.
- Check the controller display is lit; a single power cycle at the isolator may be tried only if your installer or manual allows it.
What the engineer will check
On the Versati III Monobloc (R32)
- Follow the Gree troubleshooting flowchart for this code in the service manual.
- Check water pressure, strainer/filter and air in the system.
- Check circulation pump operation and flow sensor/switch.
- Check heater safety thermostats and wiring.
Who to ask for: Heat pump engineer.
Certification: Heat pump installer competence; F-gas / flammable-refrigerant (R290/R32) handling competence for any refrigerant-circuit work.
On the Versati III Split / All-in-one (R32)
- Follow the Gree troubleshooting flowchart for this code in the service manual.
- Check sensor connector and wiring.
- Measure sensor resistance against the manual's sensor table.
- Replace sensor or PCB as indicated by the troubleshooting flowchart.
Who to ask for: Heat pump engineer.
Certification: Heat pump installer competence; F-gas / flammable-refrigerant (R290/R32) handling competence for any refrigerant-circuit work.
On the Versati IV Split / All-in-one (R32)
- Follow the Gree troubleshooting flowchart for this code in the service manual.
- Check sensor connector and wiring.
- Measure sensor resistance against the manual's sensor table.
- Replace sensor or PCB as indicated by the troubleshooting flowchart.
Who to ask for: Heat pump engineer.
Certification: Heat pump installer competence; F-gas / flammable-refrigerant (R290/R32) handling competence for any refrigerant-circuit work.
On the Versati V R290 Monobloc
- Follow the Gree troubleshooting flowchart for this code in the service manual.
- Check sensor connector and wiring.
- Measure sensor resistance against the manual's sensor table.
- Replace sensor or PCB as indicated by the troubleshooting flowchart.
Who to ask for: Heat pump engineer.
Certification: Heat pump installer competence; F-gas / flammable-refrigerant (R290/R32) handling competence for any refrigerant-circuit work.
What you might notice
Sources
- VERSATI III Air To Water Heat Pump (Monobloc) Service Manual ↗ · page p.121 (printed; PDF p.121) · Reviewed 23 September 2026
- Service Manual for VERSATI R32 SPLIT (VERSATI III Split Type Air To Water Heat Pump) ↗ · page p.108 (printed; PDF p.112) · Reviewed 23 September 2026
- VERSATI IV Split Type Air To Water Heat Pump Service Manual ↗ · page p.66 (printed; PDF p.76) · Reviewed 23 September 2026
- VERSATI V Monobloc Type Air-to-water Heat Pump Service Manual (R290) ↗ · page p.30 (printed; PDF p.33) · Reviewed 23 September 2026
A code explains what the controller detected, not a confirmed root cause.
Reviewed: 23 September 2026